From Around The WORLD
|
| |||||
|
From Around The WORLD
|
Electronic Speed Controllers For Sale: ESC Manufacturers: Associated ESC Castle Creations ESC Copter-X ESC Duratrax ESC Dynam ESC Electrifly ESC Emax ESC EZ-Run ESC Futaba ESC GM ESC Hobbyking ESC Hobbywing ESC HPI ESC JR Racing ESC Kyosho ESC Losi ESC LRP ESC Moped ESC M-Troniks ESC Mystery ESC Novak ESC Novatech ESC Powermaster ESC Qidi ESC RC Hobbies ESC Ripmax ESC Tamiya ESC Tekin ESC Traxxas ESC Yeah Racing ESC |
|
Electronic Speed Controllers For Sale: ESC Types: Airplane ESC Boat ESC Buggy ESC Helicopter ESC Micro ESC ESC With Reverse Touring Car ESC Truck ESC Waterproof ESC Radio Equipment For Sale: Frequencies: 2.4 Ghz Radio 27 Mhz Radio 29 Mhz Radio 35 Mhz Radio 36 Mhz Radio 40 Mhz Radio 72 Mhz Radio 75 Mhz Radio General Radio Items: Radio Equip (General) Crystals (All Fq) Receivers (All Fq) Servos (General) |
|
why not checkout eBay throughout the WORLD |
|
|
Custom Search
|
|
Battery Charging Ni-Cad (Nickel Cadmium) 1/ All Ni-Cad Batteries have to be Discharged soon after use. This is to avoid the dreaded "Memory" effect that on subsequent re-charges can cause a momentary drop in performance during a race. A simple discharger can be made from a car 12v bulb. 2/ Try to time your charge to complete just before a race. This will ensure maximum punch and duration. If a Ni-Cad is left to cool after a charge this advantage dissipates. 3/ The higher the charge current the more Punch the Ni-Cad battery will have (up to around 8 amps), however, the downside to this is a reduction in duration and effective battery life. 4/ Ni-Cad Batteries should be left to cool for about an hour after use before recharging. This will increase the effective life of the battery. Ni-Mh (Nickel Metal Hydride) 1/ Never charge Ni-Mh batteries at a current higher than 4.5 amps. Although these batteries can give a higher voltage than Ni-Cad Batteries, they are much more sensitive and easy to damage if charged too quickly. 2/ Charging methods for Ni-Mh batteries can also be detrimental. The best I found was the "Slope" method. Avoid "Pulse" charging as this tends to effect crystal formation detrimentally and (it seems to kill them off) thus reduces duration over time. 3/ If using a temperature cut off charger on Ni-Mh batteries set to no more than 40 Degrees Centigrade. Any higher than this can damage the crystals. 4/ It is not necessary to discharge Ni-Mh Batteries. Unlike Ni-Cad batteries they do not develop a memory. Also, if they are totally discharged they sometimes will not charge straight after and need to be coaxed with a 10 minute trickle charge. 5/ Ni Mh Batteries can be recharged shortly after use without any discernable detrimental effects. |
|
Radio Gear How to avoid Interference. 1/ The first consideration when installing your Receiver into your Electrically Powered Model is to make sure it is well away from the Negative Battery terminal, and the Motor. The Magnetic field can cause stuttering type interference at times of high current draw (i.e., Fast Acceleration) 2/ Make sure the Ariel tube is long enough for the Ariel wire. The tip of this wire is highly sensitive and should be as high, and as far away from the Motor as possible (yup, its that magnetic field prob again) 3/ If all else fails, a simple tip that often works for all RC Model enthusiasts is to wrap the receiver in Aluminium Foil, to shield against any magnetic and external radio interference. 4/ As a last resort, to protect against servo twitch, try ferrite beads. (available at Radio Shack or Maplins) These are threaded over the red, white (or yellow) and black wires of each servo. |
|
|
|
|
|
|
|
 |
| |||||
Every effort is made to ensure that information contained within the RCScrapyard site is correct and fair. However, no responsibility can be taken for errors, omissions or inaccuracies. Any complaints will be dealt with as soon as possible. © RCScrapyard |
For Sale in the USA